Desalination Plants

Desalination plants are subject to corrosive and turbulent water, coatings are essential to protect the concrete. structures and pump equipment require grout to secure them in place.

Repair, rehabilitate, coat and protect to stop corrosion. Increase asset life span with our range of specialist products below:

Products

  • E500P– HYCHEM E500P is designed as a pore filling primer to be used in conjunction with high build epoxy coatings and toppings to inhibit gassing of the high build product due to thermal movement of air between the substrate and the air space. This pore filling action is essential when the surface is to becoated with Hychem TL5.
  • E500T – HYCHEM E500T is designed to be used as fairing mortar for application to prepared concrete surfaces which are to be coated with a protective coating. The product is used for the filling and sealing of small holes formed by the removal of cement paste during water blasting and other surface preparation methods.Hychem E500T can also be used as a general purpose patching compound for rendering or making good the surface prior to theapplication of a protective top coat.
  • TL5 EPL – HYCHEM TL5 EPL is a chemically resistant high-build epoxy coating designed for use in environments where exposure to water, salt solutions, alkali and dilute mineral acids is required. The product is designed for applications of up to 6mm+ using wet on wet spray technique, but can also be trowelled in small areas where spray application is unsuitable. HYCHEM TL5 EPL is based on the same resin as HYCHEM TL5 but uses a slower hardener system to allow a longer work time. This change in hardener results in equally good sulphuric acid resistance compared to TL5.
  • TL6 – Water potable epoxy coating. Add 500ml epoxy pigment – Hychem TL6 is a specialised water potable coating suited to a large range of applications. TL6 can be roller applied to vertical and horizontal substrates including concrete and steel. TL6 is a high-build, multipurpose, solventless epoxy coating exhibiting a chemically resistant high gloss stippled finish. Hychem TL6 is suited to water potable environments. It conforms to to AS/NZS 4020/2005 testing of products for use in contact with drinking water.
  • Hygrout range
  • Geocast – GEOCAST Geopolymer is a single component, dry packaged, polymer–modified mortar with microsilica geopolymer, pozzolan, flyash and select admixtures. It is specifically designed for horizontal, vertical
    and overhead surface repairs in reinforced concrete and brick pipes, corrugated metal pipe inverts (CMP) and arches, sewer manholes and (water) wastewater structures. The GeoCast Geopolymer withstands hydrogen sulfide (H2S) corrosion. Geocast offers high early strength and long term durability. Applications to 100mm thicknesses overhead – >62 Mpa
  • Velosit: WP120 – VELOSIT WP 120 is a polymer modified cementitious waterproofing slurry for concrete and masonry. It is a good substrate for coatings and overlays. Potable Water Approved – AS/NZS 4020:2005
  • Velosit RM205 – VELOSIT RM205 Structural Concrete Repair Mortar 6 – 100 MM – 45MPa a cementitious repair mortar for concrete restoration acc. to EN 1504-9. It is used to fill large voids or build up larger cross-sections up to 100 mm. Potable Water Approved – AS/NZS 4020:2005
  • NG412
  • CW111 – VELOSIT CW 111 is a High Strength Crystalline Waterproofing slurry for concrete substrates. It is very economic and easy to apply. VELOSIT CW 111 becomes part of the concrete and creates a waterproof layer inside the concrete itself. It is especially strong against negative side water pressure. Self healing properties of up to 0.4 mm static cracks Unsurpassed strength development with more than 20 MPa after 24 h and more than 50 MPa after 28 days

Recommended Products

Product Type

Repair, rehabilitate, coat and protect to stop corrosion. Increase asset life span with our range of specialist products below:

Products

  • E500P– HYCHEM E500P is designed as a pore filling primer to be used in conjunction with high build epoxy coatings and toppings to inhibit gassing of the high build product due to thermal movement of air between the substrate and the air space. This pore filling action is essential when the surface is to becoated with Hychem TL5.
  • E500T – HYCHEM E500T is designed to be used as fairing mortar for application to prepared concrete surfaces which are to be coated with a protective coating. The product is used for the filling and sealing of small holes formed by the removal of cement paste during water blasting and other surface preparation methods.Hychem E500T can also be used as a general purpose patching compound for rendering or making good the surface prior to theapplication of a protective top coat.
  • TL5 EPL – HYCHEM TL5 EPL is a chemically resistant high-build epoxy coating designed for use in environments where exposure to water, salt solutions, alkali and dilute mineral acids is required. The product is designed for applications of up to 6mm+ using wet on wet spray technique, but can also be trowelled in small areas where spray application is unsuitable. HYCHEM TL5 EPL is based on the same resin as HYCHEM TL5 but uses a slower hardener system to allow a longer work time. This change in hardener results in equally good sulphuric acid resistance compared to TL5.
  • TL6 – Water potable epoxy coating. Add 500ml epoxy pigment – Hychem TL6 is a specialised water potable coating suited to a large range of applications. TL6 can be roller applied to vertical and horizontal substrates including concrete and steel. TL6 is a high-build, multipurpose, solventless epoxy coating exhibiting a chemically resistant high gloss stippled finish. Hychem TL6 is suited to water potable environments. It conforms to to AS/NZS 4020/2005 testing of products for use in contact with drinking water.
  • Hygrout range
  • Geocast – GEOCAST Geopolymer is a single component, dry packaged, polymer–modified mortar with microsilica geopolymer, pozzolan, flyash and select admixtures. It is specifically designed for horizontal, vertical
    and overhead surface repairs in reinforced concrete and brick pipes, corrugated metal pipe inverts (CMP) and arches, sewer manholes and (water) wastewater structures. The GeoCast Geopolymer withstands hydrogen sulfide (H2S) corrosion. Geocast offers high early strength and long term durability. Applications to 100mm thicknesses overhead – >62 Mpa
  • Velosit: WP120 – VELOSIT WP 120 is a polymer modified cementitious waterproofing slurry for concrete and masonry. It is a good substrate for coatings and overlays. Potable Water Approved – AS/NZS 4020:2005
  • Velosit RM205 – VELOSIT RM205 Structural Concrete Repair Mortar 6 – 100 MM – 45MPa a cementitious repair mortar for concrete restoration acc. to EN 1504-9. It is used to fill large voids or build up larger cross-sections up to 100 mm. Potable Water Approved – AS/NZS 4020:2005
  • NG412
  • CW111 – VELOSIT CW 111 is a High Strength Crystalline Waterproofing slurry for concrete substrates. It is very economic and easy to apply. VELOSIT CW 111 becomes part of the concrete and creates a waterproof layer inside the concrete itself. It is especially strong against negative side water pressure. Self healing properties of up to 0.4 mm static cracks Unsurpassed strength development with more than 20 MPa after 24 h and more than 50 MPa after 28 days

Recommended Products

Product Type

Need a specification ? - It’s FREE

All you needed to do was ask us !

We would love to work with you to make sure your project is a complete success so why not fill out the form below and send it to us. We will get back to you at a convenient time and work out what we need to do next. It’s as simple as that really !